ΚΑΛΑΘΙ ΑΓΟΡΩΝ
Το καλάθι σας είναι άδειο
Spinner
contact-phone
ΤΗΛΕΦΩΝΙΚΟ ΚΕΝΤΡΟ
+30 261 500 2002

TOP ΕΤΑΙΡΕΙΕΣ

ΟΛΕΣ ΟΙ ΕΤΑΙΡΕΙΕΣ

Η Telematica είναι αποκλειστικός αντιπρόσωπος των κορυφαίων εταιρειών μηχανοκίνητου αθλητισμού και ηλεκτρονικών. Περιηγηθείτε στην ευρεία γκάμα κατασκευαστών μας και εξοπλίστε το όχημά σας με προϊόντα υψηλής ποιότητας και απόδοσης.

ΔΕΙΤΕ ΟΛΕΣ ΤΙΣ ΕΤΑΙΡΕΙΕΣ
  • CloseMENU

Stator Unmolded for Harley Davidson 2000 Softail

38 Amp Alternator, OEM PN 29951-99

ACCEL Performance
Κατασκευαστής : ACCEL Performance
Κωδικός : 152109
Barcode : 743047414682
ERP Code : ACC-0675

Made from the finest components available, these high quality ACCEL Motorcycle Lectric stators are precision machine-wound and produce the highest output possible. The windings are then coated to maintain isolation of the pure copper windings from potential grounding sources. Some part numbers are available in an over molded configuration for maximum isolation. As always, ACCEL believes in providing the highest quality products and backs each stator with a limited lifetime replacement warranty. Stator, Lectric, Unmolded, Harley-Davidson.

13.UPS
Official ACCEL Performance Distributor
Supplier Warranty
* Εντοπίστε το πακέτο σας οποιαδήποτε στιγμή μέσω του tracking number που θα σας στείλουμε μέσω SMS και e-mail

Πληροφοριες προιοντος

Charging Problems

Check the Stator:

  1. Disconnect the regulator from the stator at the terminal inside the crankcase.
  2. Check for continuity between either stator pin and the crankcase. Continuity indicates that the stator is grounded and needs to be replaced.
  3. Check the resistance between the stator pins. A reading of 0.1 to 0.2 ohms should be present. A lower reading requires that the stator be replaced.

Check the Output:

  1. Again disconnect the regulator, and connect a voltmeter set to AC volts across the stator terminals. With the engine running at 2000 rpm, there should be a reading of 32-40 AC volts. The output will increase or decrease 16-20 AC volts for every 1000 rpm.

Check the Current Draw:

  1. With all accessories, ignition, and headlamp high beam turned on, read the current draw.
  2. The current draw should be at least 3.5 Amps lower than the output listed in the SPECIFICATIONS section of the Harley-Davidson service manual. You may have too many accessories drawing power for the system to handle.

How Do I Polarize My Generator?

  1. A generator that is not polarized will burn relay points, cause a dead battery, or damage to the generator.
  2. Momentarily touch a jumper wire between the BAT and GEN terminals on the generator.

Παρομοια προιοντα

ΕΠΙΚΟΙΝΩΝΙΑ
+30 261 500 2002
Call Center
Telematica Contact Email
Email Message
ΩΡΕΣ ΛΕΙΤΟΥΡΓΙΑΣ
Δευτέρα - Παρασκευή 9:00 - 20:00
Σάββατο - Κυριακή Κλειστά
W3C HTML5 validator